Home » Technology » Reasons behind a Vario CDI being Burnt and Effective Remedies

Reasons behind a Vario CDI being Burnt and Effective Remedies

The cause of the Vario CDI burning is certainly not something to be taken lightly. Burning Vario CDI often makes motorists panic and want to know the cause. After that, you can solve the motor CDI problem.

CDIs or Capacitor Discharge Ignition become an important electrical component in the motor. One of the damage to the CDI Vario that might occur is the burning CDI.

Read Also: How to Fix Dead CDI, Adjust to the Cause

This condition can occur due to several factors. Burning CDI is likely due to a short circuit or too much current.

The Cause of Burning Vario CDI Needs to Be Known

CDIs or Capasitor Discharge Ignition has an important role in motor ignition that you cannot underestimate. Because, if the CDI dies or burns, then you can’t drive the Vario motorbike.

Ignition resume on fuel cannot occur. As the name implies, CDI will work by placing an electric current. Starting from the generator which is released to the coil after the signal from the pulser is obtained.

If you want to recognize the condition of the Vario CDI, you can use a voltmeter. By using this tool, you can find out the voltage from the CDI component on your Vario motorcycle.

To be able to fix dead CDI to fruition, it would be better to get to know it in detail. The use of the voltmeter to handle the CDI is off.

Even before repairing a dead CDI, you can do some testing first. However, if the motorbike you are driving suddenly dies due to a burning CDI element problem, make sure you know the cause of the Vario CDI burning. The following are some of the causes.

Unstable Current Flow

One of the causes of burning CDI due to electrical voltage that is not constant. In addition, it can also occur due to a decreased battery voltage, but the motor is still running.

Electrical short circuit

CDI problem on a burning motor due to an electric short circuit. Inappropriate CDI installation can also be the cause of the motor turning off suddenly and emitting thick smoke.

Read Also: As a result of Damaged Motor CDI, the Motor Turns Off Suddenly and Hard to Start!

This can also occur from the state of the cable under different conditions to cause a short circuit, then burn.

Overheating

Vario CDI can also burn when conditions are too hot or overheating. This can happen if the Vario motor components are exposed to direct sunlight.

Even if there is a problem with the engine cooling system. Until finally making the engine temperature to be too high.

Causes Burned Vario CDI Component Damage

Damage to components in the ignition system, such as the stator or flywheel, can also cause the Vario CDI to burn. This occurs due to problems with the electricity so that the electric current is excessive or experiencing a short circuit.

Poor CDI Quality

CDI Vario with poor quality or not original can also make the CDI burn. This happens because the CDI is not able to handle large electrical loads. If experiencing design or production problems on the CDI.

Burnt CDI or small ignition, of course you can overcome it in other ways. After knowing the cause of the Vario CDI burning, it would be better to fix it immediately by dissecting the components.

Repair Burnt Vario CDI

If you already know the cause of the burning CDI, then need to make repairs. When the Vario CDI burns, it is necessary to carry out maintenance and handling due to the damage problem.

burnt CDI, it would be better not to force it on. Especially when you force the Vario motorbike to keep going. When the motorcycle CDI has a problem, you can immediately replace it with a new one.

Generally when the CDI is damaged it is very rare that it can be repaired to its original condition. For that, you need to do simple routine maintenance by cleaning it.

You can also routinely check electrical cables with high voltage, so they don’t experience a short circuit. If it does burn seriously enough, it’s best not to touch it.

Read Also: Causes of Damaged Motorcycle CDI, Know Before Buying a New One

Also don’t even try to fix it. So, the most appropriate step when experiencing Vario CDI burning conditions is to immediately take it to the repair shop.

It is important to always carry out routine maintenance and checks on the Vario motorbike ignition system. Especially for CDI components to prevent damage and burning of the motor components.

You really need to find out what causes the CDI Vario to burn out. After that, you can repair or replace it with a new quality CDI. (R10/HR-Online)

This post was last modified on April 1, 2023 5:07 AM

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.