How to replace the motorcycle disc caliper seal is quite easy. It’s good if you try to replace it yourself without having to go to a repair shop.
All motor components have a performance that has an important function.
These components must be able to work optimally so that their performance is also good. One way to do this is by providing regular maintenance.
If you only use the motorbike without taking care of it, it is certain that the condition will not be as good as before. Components that continue to work over time will wear out and be damaged.
So you need to replace it regularly. For that, doing maintenance or service is one of the important things and you must do it.
One component that has an important role is the braking system. Without braking it will cause you to experience problems, especially accidents.
In braking there is a component whose function is quite vital, namely the disc caliper.
Sometimes it sounds trivial, but how to replace the motorcycle disc caliper seal must be considered properly. Its quite important role makes you have to pay special attention.
Also Read: How to Remove Motorcycle Caliper Pistons Independently and Easily
How to Replace the Right Motorcycle Disc Caliper Seal
Replacing motorcycle components is an important thing to pay attention to. Components that have been damaged must be replaced immediately in order to maintain their performance.
If you can’t replace it yourself, it’s best to take it to a professional repair shop. Usually the caliper seal is damaged due to the amount of dirt that has accumulated because the motor has been used for a long time.
If this condition continues to occur, of course the motorcycle disc brakes can be problematic. One of them brake failure due to leaking brake fluid.
Actually you can handle it yourself without having to go to the workshop. If you want to try disassembling, make sure you know the proper way to repair.
First
The first step should be to remove the brake calipers from the front shockbreaker or rear swing arm. You can use how to replace the motorcycle disc caliper seal with the help of L 8, T10, and T8 keys.
Unscrew the fixing bolt using a T8 wrench, remove the brake hose using a T10 wrench. Meanwhile, to remove the caliper piston, you can use the compressor air pressure while being pulled slowly.
Also Read: How to clean a crusty motorcycle piston without having to disassemble the engine
Second
If the first step is successful, then you can proceed to the next method. When the piston is removed, the seal will appear.
You can immediately replace it with a new one. You can use a screwdriver to help remove or pry the caliper seal.
Third
Clean all calipers using soapy water. Dry and insert the new piston seal until it is in the correct position.
How to replace the motorcycle disc caliper seal, then you can return the piston to its original state.
Fourth
The next step is to reassemble the motorcycle disc calipers and bleed the brake fluid. Make sure it is fully charged in the braking system chamber.
Immediately check again before you use a motorcycle for long trips. Make sure the brakes can function normally and optimally.
If the condition is normal, then you can successfully replace the motorcycle disc caliper seal.
Also Read: Motorcycle Disc Brakes Drag, Recognize What Causes It
How Disc Calipers Work
As has been done since the beginning if the motorcycle components have a fairly important role. If the caliper is in normal condition, the piston will condense on both sides.
However, if the caliper expands, the piston will work to push the brakes. With this, braking occurs which hits the rotor, thus making the vehicle stop.
Calipers are components of the disc braking system. Discs consist of various types of components concerned.
If one problem occurs it will cause problems in other components. For that, provide proper care so that all motor components can function optimally.
The components in the braking system other than calipers are brake linings, disc discs, caliper brackets, brake pistons, piston seals, reservoir tanks, master cylinders, brake fluid, and brake boosters.
All components of motorcycles from the past until now have the same appearance. Though all components have their respective roles.
If you are late to take care of it, it could be that one component is problematic and the other is affected. You can do how to replace the motorcycle disc caliper seal easily. Make sure to replace it carefully. (R10/HR-Online)
–
