ANTEC P10 FLUX Mid-Tower silent case
ANTEC launched the new “P10 FLUX” Mid-Tower silent chassis, which is a derivative of the DF600 / DP502 that was listed earlier. It features quietness and excellent heat dissipation. It adds an innovative 5 fan F-LUX airflow architecture to improve the airflow inside the chassis. The difference in heat dissipation performance is that P10 FLUX abandons the full-frame glass design, and adds high-density sound-proof foam materials to the side panels, top and front doors on both sides to effectively absorb and block internal noise. Players who pursue Ningyin may wish to consider it.
P10-FLUX and DP502 FLUX / DF600 FLUX share an inner cage. The difference is that the front panel is changed to a silent cover design. The appearance design is mainly simple and flat. The plain black body front panel is treated with metal wire drawing. The festival shoots a sense of material layering, simple and low-key without fancy decoration, very suitable for users who like simple and professional texture.
Although the P10 FLUX adopts an uncovered panel design, in order to improve the air intake effect, 11mm air inlets are reserved on the four sides of the cover and the body. The front fan is equipped with a detachable dust screen. The door can be opened to the left. Or open to the right, so don’t worry about placement, it’s very considerate.
The I/O Panel of ANTEC “P10 FLUX” is located at the top of the front panel. It provides Power switch button, fan speed button, 2 sets of USB 3.0 Type A ports, 3.5mm headphone and microphone audio interface, which is quite complete.
The biggest selling point of ANTEC P10 FLUX Mid-Tower is quietness, quietness and quietness….sound effect. Thick high-density sound insulation materials are added to the side panels at both ends, the front panel and the top of the chassis to absorb and block the chassis. For users who are looking for a silent system, 10 FLUX will be the choice of players who are looking for silent system.
Support card length 40.5cm Chamber design
▲ ATX, Micro-ATX and ITX Form Factor motherboard
The ANTEC “P10 FLUX” Mid-Tower case is made of SPCC cold rolled steel plate and ABS plastic material. The size is 477mm x 220mm x 486mm. It supports ATX, Micro-ATX and ITX Form Factor motherboards. The CPU position can support up to 17.5cm high heat dissipation. At the same time, it can install a graphics card up to 40.5cm long, which is enough to meet the installation requirements of high-end gaming hardware.
▲ Chamber compartment at the bottom ▲ Supports power supply with a maximum length of 20.5cm
There is a Chamber below to separate the motherboard and power supply area, providing good cable management space and isolating noise. It supports a power supply with a maximum length of 20.5cm. The Drive Bay in the Chamber uses a detachable design, allowing the chassis to be expanded to 1500W or above A high-wattage power supply.
3 + 3 storage expansion capacity
▲ 28mm cable management layer space
▲ Removable 3.5-inch Drive Bay ▲ 3.5-inch HDD installation location
▲ Two 2.5-inch SSD/HDD bays ▲ 2.5-inch SSD/HDD installation location
Innovative F-LUX air flow architecture
ANTEC P10 FLUX is the first ANTEC case to incorporate F-FLUX airflow design. The case comes with 5 fans, including 3 12cm ARGB fans at the front, 1 12cm fan at the rear, and 1 12cm anti-blade fan above the Chamber. A ventilation fence is added under the board, and the most direct air duct design is planned.
The main function of the F-LUX airflow design is to improve the heat dissipation performance of the VGA. The traditional GPU air channel and the VGA fan flow in an L-shape. When the wind is drawn in, the force of the airflow needs to be offset. Adding a reverse blade fan below can form a damper to allow the GPU air channel The direction of flow is changed to directly face the VGA card, making it easier for the VGA fan to draw in the wind.
Another major selling point of “P10 FLUX” is that it comes with 5 cooling fans. Players no longer need to spend extra money to buy a fan. There are 3 front fans, 1 rear fan, and 1 12 cm fan above the chamber to prevent dust and Easy to clean, the front, right side panel, and power supply are also provided with detachable dust screens, which are convenient for users to clean and make it easier for users to clean and keep the inside of the case clean.
In terms of cold exhaust, no matter the front end can be installed with a maximum of 280mm / 360mm water-cooled radiator, the rear can be installed with a maximum of 120mm water-cooled radiator. For the Mid-Tower chassis, it is very abundant and very suitable for water-cooled players.
ANTEC P10 FLUX Mid-Tower silent case
Price: HK$599
Enquiry: Felton (2273-8393)
Editor’s comment:
The silent design of the chassis has always been mainly in the middle and high-end. The ANTEC P10 FLUX is aimed at the entry-level market. It caters to those who want to try the silent model and have a small budget. High-density sound insulation materials are added to the front, top and left and right side panels. Attached with 5 12cm silent fans and supports F-LUX air flow architecture technology, it is definitely a gospel for silent players.
